Ohm's Law Calculator: Find Voltage, Current, Resistance and Power
This free Ohm's law calculator helps you solve electrical circuit questions using the values you already know. Enter any supported pair of voltage, current, resistance or power values and see the remaining values with a step-by-step explanation. The first tool works with simple ideal DC resistive circuits. The other tabs handle series and parallel resistors or basic AC power calculations. It is designed for electrical engineering students, electronics beginners, school physics classes, diploma practicals and anyone revising basic electricity.
Many learners search for an ohm law calculator, ohm laws calculator, ohm calculator or current resistance voltage calculator when they want to verify homework without manually rearranging every formula. Those names usually refer to the same relationship: an electrical voltage creates current through resistance. This page also acts as an ohm and watt calculator because it shows the electrical power associated with the calculated voltage and current.
Use the calculator above before reading the guide. It is ready with a simple example: a 12 V supply across a 6 Ω resistor. The result is 2 A of current and 24 W of power. On a mobile screen, the input fields and answer are kept together so you can calculate without searching through a long introduction.
What Is Ohm's Law?
Ohm's law is one of the most important principles in electricity. It says that the current through an ohmic conductor is proportional to the voltage across it when resistance remains constant. German physicist Georg Simon Ohm described this relationship in the nineteenth century. The familiar formula for Ohm's law is V = I × R. Here V means voltage in volts, I means current in amperes and R means resistance in ohms. The symbol Ω represents the ohm, the standard unit of electrical resistance.
Students also call it the ohm formula, Ohm's law equation or current resistance voltage formula. A class textbook may use E instead of V for electromotive force or voltage. For a simple resistor circuit, E = I × R expresses the same relationship. The formula for current voltage and resistance can be rearranged, so you only need two known quantities to work out the third. It helps explain how a current changes when a resistor is replaced or a battery voltage is increased.
The Ohm's law of electricity is most directly applied to ohmic materials at a reasonably stable temperature. A lamp filament, semiconductor diode or other nonlinear component may not have a constant resistance when voltage changes. Calculating R = V/I gives a resistance at that operating point, but it does not automatically mean the same resistance applies at every other voltage.
All Important Ohm's Law and Power Formulas
The Ohm's law and power formula connect voltage, current, resistance and electrical power. Power is the rate of electrical energy transfer and is measured in watts (W). In a resistive DC circuit, P = V × I. You can combine this with V = I × R to calculate power using resistance and either current or voltage.
| Find | Formula | Known values |
|---|---|---|
| Voltage (V) | V = I × R | Current and resistance |
| Voltage (V) | V = P ÷ I | Power and current |
| Voltage (V) | V = √(P × R) | Power and resistance |
| Current (I) | I = V ÷ R | Voltage and resistance |
| Current (I) | I = P ÷ V | Power and voltage |
| Current (I) | I = √(P ÷ R) | Power and resistance |
| Resistance (R) | R = V ÷ I | Voltage and current |
| Resistance (R) | R = V² ÷ P | Voltage and power |
| Resistance (R) | R = P ÷ I² | Power and current |
| Power (P) | P = V × I = I²R = V²/R | Appropriate positive values |
These are the common electrical laws and formulas students use for voltage, current and resistance calculations. You may find the expressions described as the power resistance voltage formula, power voltage resistance formula, Ohm's law formula for power, Ohm's law formula power or Ohm's law power formula. They are different arrangements of the same underlying equations.
How to calculate voltage
If current and resistance are known, multiply current by resistance. For example, a 3 A current flowing through an 8 Ω resistor requires 24 V across that resistor. Enter Current & Resistance in the calculator. It will show the voltage and calculate 72 W of dissipated power. If you know current and power instead, divide P by I to get voltage. These methods answer many common Ohm's law calculations examples from school and engineering practicals.
How to calculate current
Divide voltage by resistance. A resistor of 6 Ω connected across 12 V carries 12 ÷ 6 = 2 A in an ideal resistive circuit. This is the standard use of an Ohm's law resistance calculator or V I R calculator: instead of guessing, select the two known measurements and the tool computes the missing one. For a fixed voltage, doubling resistance cuts current in half.
How to calculate resistance
Divide voltage by current. If a device draws 0.5 A from a 10 V source, its calculated resistance at that operating point is 20 Ω. Another method applies when power and voltage are known: R = V²/P. These relationships explain why an ohm calculator resistor mode is helpful for quick checks during classroom experiments. Always use consistent electrical units before calculating.
How to calculate electrical watts
Multiply voltage and current for resistive DC power. For example, a 5 V supply delivering 2 A transfers 10 W. If the circuit has 5 Ω resistance and the current is 2 A, the power is I²R = 2² × 5 = 20 W. An Ohm's law calculator watts mode is particularly useful when a problem asks whether a resistor is likely to dissipate a small or large amount of energy. Actual resistor wattage ratings require safety margin and operating-temperature considerations, not just a calculator result.
Ohm's Law Calculator with Solution: Worked Examples
A good Ohm's law calculator with solution should do more than show a single number. It should tell you which formula was used and how the known values were substituted. Below are several examples you can reproduce in the first tab. The same method applies whether you work in volts, millivolts, amperes, milliamperes, ohms or kilo-ohms, provided that values are converted to consistent base units.
Example 1: 12 V and 6 Ω
You have a 12 V DC source and a 6 Ω resistor. To find the current, write I = V/R. Substituting the values gives I = 12/6 = 2 A. Power is P = V × I = 12 × 2 = 24 W. This example shows why current increases when applied voltage increases but resistance stays constant.
Example 2: 24 V and 3 A
A circuit operates at 24 V and draws 3 A. Resistance is R = V/I = 24/3 = 8 Ω. Power is P = 24 × 3 = 72 W. This exercise combines a current resistance voltage calculator with a power calculation in the same problem. Enter Voltage & Current and the calculator fills in the other quantities.
Example 3: 8 Ω and 18 W
A resistor dissipates 18 W and has a resistance of 8 Ω. Since P = I²R, rearrange the equation to get I = √(P/R) = √(18/8) = 1.5 A. Voltage is V = IR = 1.5 × 8 = 12 V. The same positive-magnitude method is used in the calculator. When only R and P are specified, it reports the conventional positive voltage and current magnitudes.
Example 4: Convert milliamperes and kilo-ohms
If the current is 20 mA and resistance is 1 kΩ, convert 20 mA to 0.02 A and 1 kΩ to 1000 Ω. Voltage is V = 0.02 × 1000 = 20 V. Power is 20 × 0.02 = 0.4 W. These conversions matter in electronics projects because components and instruments frequently use small currents but relatively large resistance values.
Series and Parallel Resistance Calculator
Several resistors connected together do not always behave like one resistor with the sum of all printed values. The result depends on whether the resistors form a series chain or parallel branches. That is why this page includes an Ohm's law calculator series parallel circuits tab and an Ohm's law calculator multiple resistors option. It displays equivalent resistance, supply current, total power and individual resistor values.
Series resistor circuits
In series, the resistors form one path. The same current flows through every resistor, and the individual voltage drops add up to the supply voltage. Equivalent resistance is Rₑq = R₁ + R₂ + ... + Rₙ. For example, 100 Ω and 220 Ω in series produce 320 Ω. With a 12 V source, the current is 12/320 = 0.0375 A, or 37.5 mA.
An Ohm's law calculator 2 resistors is useful when you need two-component examples, but the tool here also works with larger lists. It lets you see each resistor's voltage drop as I × R. The total of those drops should equal the supply voltage, apart from small rounding differences in displayed values.
Parallel resistor circuits
In parallel, each resistor is connected across the same source voltage. The current divides between branches. The formula is 1/Rₑq = 1/R₁ + 1/R₂ + ... + 1/Rₙ. For two resistors, you can also use Rₑq = R₁R₂/(R₁ + R₂). For example, 100 Ω and 200 Ω in parallel produce approximately 66.667 Ω. With 12 V applied, their individual currents are 0.12 A and 0.06 A, giving 0.18 A total.
Students searching for an Ohm's law calculator for parallel circuits, Ohm's law calculator parallel circuit or Ohm's law calculator parallel circuits can choose Parallel Resistors in the second tab. The diagram changes from a single chain to several current paths. It also includes component current and power in a small table. A zero-ohm ideal parallel branch is a short circuit; the calculator flags that case rather than inventing a finite current.
Difference between series and parallel
Series connections increase the equivalent resistance as more positive resistors are added. Parallel connections reduce equivalent resistance as additional branches are added. In a pure series circuit current is common; in a pure parallel circuit voltage is common. These differences appear often in class 10–12 physics, electrical diploma courses, and beginner electronics examinations.
AC Ohm's Law Calculator, Watts and Power Factor
Alternating current introduces a distinction between resistance and impedance. The basic relationship between RMS voltage and current in a sinusoidal AC circuit is based on impedance magnitude, while real power depends on power factor. An AC Ohm's law calculator is sometimes used as a broad name for these calculations. This page's AC tab specifically computes real, apparent and reactive power magnitude from RMS values and a power factor; it is not a general complex-impedance or reactance solver.
For single-phase sinusoidal AC, apparent power is S = V × I in volt-amperes (VA). Real power is P = V × I × PF in watts. Reactive power magnitude is Q = S × √(1 − PF²) in volt-amperes reactive (var), under the usual sinusoidal assumptions. Power factor PF is typically between 0 and 1 when stated as an absolute magnitude. For example, 230 V, 5 A and 0.8 power factor give S = 1150 VA, P = 920 W and Q = 690 var.
Balanced three-phase power
A 3 phase Ohm's law calculator or Ohm's law calculator 3 phase is often used by learners solving balanced motor and electrical-machine problems. For a balanced three-phase system, total real power is P = √3 × Vₗᵢₙₑ × Iₗᵢₙₑ × PF. Here voltage is line-to-line RMS voltage, current is line RMS current, and PF is the power factor. Apparent power uses the same formula without PF.
For example, if the balanced system uses 400 V line-to-line RMS, 10 A line current, and PF = 0.8, then real power is approximately 5.54 kW. This three-phase relationship is not identical to multiplying the values by three without considering how line and phase quantities are defined. The calculator uses the line-voltage and line-current method and states that assumption beside the inputs.
Real AC networks can include harmonic distortion, changing loads, reactive elements and power factor conventions beyond this elementary model. When power factor is not the cosine of a single sinusoidal phase angle, the simple power triangle does not capture every distortion component. The outputs are suitable for basic educational exercises, not for engineering certification or electrical installation design.
How to Use the Ohm's Law Online Calculator
For people searching how to use Ohm's law calculator, start with the kind of problem you have. If you are given voltage and resistance, choose that input pair rather than trying to enter four values at once. If you know current and power, choose Current & Power. The tool automatically applies the matching formula, checks the inputs and calculates the standard positive-magnitude solution.
- Open the Ohm's Law tab and select the two known quantities.
- Enter the values and select suitable units: V, mV or kV for voltage; A, mA or µA for current; Ω, kΩ or MΩ for resistance; and W, mW or kW for power.
- Tap Calculate. Read the large result and the four calculated electrical values.
- Look at the electrical circuit visual and expand the step-by-step explanation to see the formula substitution.
- For multiple resistors, switch tabs and enter a comma-separated list of component resistance values.
This Ohm's law online calculator and Ohm's law formula calculator work directly in the browser, without registration or an account. Values are not sent to a server for calculation. The page is useful as a quick study check before you copy the formula and solve the next question yourself.
What Is the Difference Between Ohm's Law and Watt's Law?
Ohm's law relates voltage, current and resistance: V = IR. Watt's law describes electric power: P = VI. When you combine them you can write power as P = I²R or P = V²/R in a simple DC resistor circuit. The Ohm's law power calculator on this page shows all four quantities together so you can compare them.
If you have voltage and resistance, the current comes first and then power. If you have voltage and power, current is P/V and resistance is V²/P. If you know current and power, voltage is P/I. If you know resistance and power, square roots are used to find current and voltage magnitudes. The rules are related but answer different questions, so learn to identify what is known before choosing a formula.
Understanding Units Used in Circuit Calculations
Voltage is measured in volts (V), current in amperes (A), resistance in ohms (Ω) and power in watts (W). A milli-unit means one thousandth of a base unit, and a kilo-unit means one thousand base units. For example, 500 mA equals 0.5 A, 2 kΩ equals 2000 Ω, and 1 kW equals 1000 W. Working in base units avoids mistakes such as treating 20 mA as 20 A.
| Quantity | Small unit | Base unit | Large unit |
|---|---|---|---|
| Voltage | 1 mV = 0.001 V | Volt (V) | 1 kV = 1000 V |
| Current | 1 mA = 0.001 A | Ampere (A) | 1 kA = 1000 A |
| Resistance | 1 mΩ = 0.001 Ω | Ohm (Ω) | 1 kΩ = 1000 Ω |
| Power | 1 mW = 0.001 W | Watt (W) | 1 kW = 1000 W |
The interactive calculator supports common units directly. If you are solving a question manually, convert inputs into base units first, use the formula, and then convert the result into the requested unit. For example, a computed result of 0.025 A can also be written as 25 mA. A calculated resistance of 4700 Ω can be written as 4.7 kΩ.
Common Mistakes in Ohm's Law Calculations
- Mixing units. Using 10 mA as though it means 10 A produces a result a thousand times too large. Check prefixes before substitution.
- Confusing voltage and power. Volts and watts are not interchangeable. A 12 V source does not imply a fixed 12 W load.
- Adding parallel resistances. Direct addition works for series resistors only. Parallel networks require reciprocal sums.
- Ignoring zero denominators. A zero resistance in the ideal V/R expression is a short circuit, not a normal finite-current answer.
- Treating AC like simple DC. In AC circuits the phase relationship and impedance can matter. Real power is not always equal to the product of RMS voltage and current.
- Forgetting practical limits. A resistor's rated power, temperature rise and circuit protection affect safe component selection.
Where Students Use an Ohm's Law Calculator
School physics students use these formulas to answer electricity chapters involving circuits, current and energy. Diploma and ITI learners apply them during electronics labs and practical exercises. Engineering students use them as a foundation before studying Kirchhoff's circuit laws, Thevenin's theorem, impedance, network analysis and electrical machines. Hobbyists may check circuit exercises before selecting components for low-voltage projects.
The series and parallel mode helps explain why two resistors behave differently depending on how they are connected. The AC power mode introduces the difference between watts and volt-amperes. The visible circuit diagrams make the relationships easier to remember than a list of equations alone. For resistor-band identification, use the related Resistor Color Code Calculator rather than trying to calculate colour bands from Ohm's law.
Frequently Asked Questions
1. What is the formula for Ohm's law?
It is V = I × R, where V is voltage, I is current and R is resistance. Rearrange it as I = V/R or R = V/I to find the unknown quantity.
2. How do I calculate resistance with Ohm's law?
Divide voltage by current: R = V/I. The result is in ohms when the voltage is in volts and current in amperes.
3. How can I calculate watts?
For a DC resistor, multiply voltage and current: P = VI. You may also use P = I²R or P = V²/R when appropriate.
4. Can I use this for two resistors?
Yes. Open the Resistors tab, enter two values and choose whether they are in series or parallel. You may also enter more than two resistors.
5. How does parallel resistance work?
Each branch has the same voltage, and equivalent resistance is calculated using the sum of the reciprocals of individual resistances.
6. How is single-phase AC power calculated?
Under the sinusoidal AC model, real power is P = V(rms) × I(rms) × PF, where PF is the power factor magnitude.
7. How is three-phase real power calculated?
For a balanced system using line quantities, P = √3 × V(line-to-line) × I(line) × PF.
8. What if a resistor value is zero?
In the ideal model, a zero-ohm path across a positive voltage source is a short circuit with no finite current solution. The resistor calculator flags that case.
9. Why can a calculated current be very high?
A small entered resistance at a large voltage produces a large ideal current. Real power supplies, wires and components have limits that are not represented by this simplified model.
10. Is this an accurate way to size real wiring or equipment?
No. It is an educational calculator. Wiring and power-system design require relevant standards, protective-device ratings, temperature limits, fault levels and qualified engineering assessment.
11. Can I use the calculator with millivolts or milliamperes?
Yes. The main tab accepts common prefixes and converts each input internally before solving.
12. Does a three-phase system always use the same formula?
The √3 line-voltage formula assumes a balanced three-phase system. Unbalanced circuits require more detailed per-phase analysis.
Practice Ohm's Law Online
Return to the calculator at the top and experiment with different values. A practical way to learn is to calculate the same circuit twice using two different pairs of known quantities and compare the answers. Begin with V = IR and P = VI, then try multiple resistors or basic AC power calculations. This reinforces the relationships between volts, amps, ohms and watts without requiring a separate software installation.
Educational references: Fluke — What is Ohm's Law? and Fluke — Electrical Measurements and Formulas. Calculated examples use idealized circuit models.